The Extraflame boiler is a great heating solution developed from the most All Extraflame products are built in compliance with the following Directives: 89/ . ‘Pellet refill pipes on store’. ‘Feed auger system routed outside to wooden clad 3 tonne storage’. ‘Extraflame LP30 plumbed to heat house and swimming pool’. Extraflame LP30 Manual Online: Alarms Table. ALARMS TABLE ALARMS Reason Indicates the presence of an alarm. Flue gas motor fault Flue gas probe fault.
|Published (Last):||10 September 2006|
|PDF File Size:||9.9 Mb|
|ePub File Size:||19.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
Biomass Parts and Service Spares, Boiler Spares & Parts
Blow Air Fitting Essentials: Insulation, finishings, covering and safety recommendations The coverings, independently from the materials from lpp30 they extraflaame made, must constitute a self-supporting construction with respect to the heating block and not be in contact with it.
For the heat generator appliances equipped with electric fan for expelling combustion products, the instructions below must be followed: Please enter a valid postcode.
The diameter of the minimum net transversal section of the valve inlet must not be lower than 15 mm.
Gradually open the load cock ensuring that the air venting valves work regularly. The use of counterslope elements is forbidden.
Take a look at our Returning an item help page for more details.
The pressure upstream from the cooling circuit must be at least 1. As previously described, when installing, all national, regional, provincial and town council Standards in force provided by the country in which the appliance has been installed must be complied with.
If water leaks, he must close the water supply and promptly inform the after-sales technical service. It is recommended to contact the qualified technician if extrafflame of the rearms should be triggered, so as extrsflame verify the cause.
The tank must be full of pellets The combustion chamber must be clean The burn pot must be completely free and clean Check the hermetic closure of the fire door and the ash drawer Check that the power supply cable is connected correctly The bipolar switch in the rear right part must be positioned on 1. The chimney cap must not have mechanical intake means.
The insertion of a three-way intercepting valve which allows connection between the vessel and the atmosphere for maintenance operations, is allowed.
Controls procedure From the main screen, turn P to select the set temperature icon Press P to confirm Turn P to adjust the temperature Confirm and memorising by pressing P To exit without memorising, press key P1 set ho 76 c Set extaflame The following menu allows to set the power. Sunday prg2 off set prg2 start – prg3 The image is given as an example.
If you perform More information. Installations not allowed In the room where the heat generator will be installed the following must not pre-exist or be installed: Diagrams in this brochure fxtraflame describe connection principles.
WELDED GRATE-BRAZIER UNITLP30 Nordica Extraflame
Get the item you ordered or your money back. Aside from programming it, activate it as well.
Such area has different dimensions and configuration depending on the covering inclination angle. In case of more heat generators which feed the same plant or the same secondary circuit, each heat generator must be connected directly to the expansion vessel or plant expansion vessels unit, altogether dimensioned for the total volume of water contained in the same plant or the same extrzflame circuit.
Unauthorized duplication, reproduction prohibited. If coverings in combustion material or sensitive to heat exist in the space above the generator, an insulating and non combustible protection diaphragm must be inserted.
The stove has been designed to function in any climatic condition also critical. Technical After-sales Service in the extrflame of intervention.
lp14 – lp20 – lp30 – La Nordica
The purchase date must be validated by the possession of a valid fiscal document issued by the dealer. Smoke channel or fittings figure 2 To mount the smoke channels, non-flammable elements will have to be used, ideal for resisting combustion products and their eventual condensing.
If the alarm persists and the above listed conditions have been checked, contact the qualified after-sales assistance centre.
The figure below shows the burn pot. If the water temperature drops, exceeding the pre-set parameters, the machine will switch back etraflame. Such device must be protected against accidental manoeuvres. An additional expansion vessel must be installed for a higher content of water.