Post Jobs


BMs – Top class digital multimeter made by Brymen. counts (5 4/5 digit), High Performance, User-oriented innovative features. Unbeatable 1µV. USER’S MANUAL BM BMCF 1 1) SAFETY This manual contains .. BRYMEN’s warranty does not apply to accessories, fuses, fusible resistors, spark . Thanks Lightages: + didn’t know TME also ships to the Netherlands prices are looking good indeed and no problem with customs since it’s.

Author: Arashigis Virr
Country: Uzbekistan
Language: English (Spanish)
Genre: Video
Published (Last): 1 March 2018
Pages: 273
PDF File Size: 6.34 Mb
ePub File Size: 12.74 Mb
ISBN: 207-1-15355-821-1
Downloads: 18312
Price: Free* [*Free Regsitration Required]
Uploader: JoJolar

It can also be loaded way beyond seconds at 1A, and has a fast acting characteristic of below 0.

BM857 BM859CF

Keep your fingers behind the finger guards of the test leads during measurement. You can also use a plug adapter Bkb32 Optional purchase with banana pins to K-type socket to adapt other standard K type mini plug temperature probes.

An OL indicates an open diode defective. In voltage or current functions, press the Hz push button momentarily to activate or to exit Line Level Frequency measuring function. Large value capacitors should be discharged through an appropriate resistance load.


Note bm8559cf Examples include household, office, and laboratory appliances. NMRR is typically specified in terms of dB decibel. Note — Examples include electricity meters and primary over-current protection equipment.

Do not measure any current that exceeds the current rating of the protection fuse. The bm859ff beeps when new maximum or minimum reading is updated.


The meter is intended only for indoor use. Do brymem attempt a current measurement to any circuit where the open circuit voltage is above the protection fuse voltage rating.

Lift the end of the case bottom nearest the input jacks until it unsnaps from the case top. It’s a community-based project which helps to repair anything. Do not operate with open case. Lift the battery access door and thus the bm859cg compartment up.

Continuity function is convenient for checking wiring connections and operation of switches. Analog bar-graph The analog bar graph provides a visual indication of measurement like a traditional analog meter needle.

In measuring non-sinusoidal waveforms, however, significant errors can be introduced because of different scaling factors relating average to RMS values. If the reading shows zero, select higher sensitivity.

Loosen the 2 screws from the battery access door of the case bottom. Note — Examples include switches in the fixed installation and some equipment for industrial bm8859cf with permanent connection to the fixed installation. Any other readings indicate the diode is resistive or shorted defective. In other words, the meter will intelligently avoid entering the APO mode when it is under normal measurements.

If the Hz reading is unstable, select lower sensitivity to avoid electrical noise. Distorted waveforms with the presence of DC components and harmonics may cause: This grymen characteristic also matches our meter nicely. Unlike the Line Level Frequency measuring function as previously stated, this Logic Level Frequency function is set only at the highest input sensitivity to measure digital type electronic signals.


Dual channels T1-T2 readings require 2 probes. The series fusible resistors and the spark gaps should then be replaced by qualified technician. In many cases the suspected component must be disconnected from bryemn circuit to obtain an accurate reading. However, if BRYMEN determines that the failure was caused by misused, altered, neglected, or damaged by accident or abnormal conditions of operation or handling, you will be billed for the repair. Suspected open circuit voltage should be checked with voltage functions.

Always set the instrument to the highest range and work downward for an unknown value when using manual ranging mode. These voltage levels pose a potential shock hazard to the user.

Brymen BMCF Manuals

Reverse the test leads connections reverse biased across the diode. Press and hold the button for 1 second or more to resume auto-ranging mode. Press button momentarily to toggle between 5 full digits and 6 full digits Hz readings.