Post Jobs

ASTM F1929-98 PDF

The current test method is ASTM F dye penetration. . ASTM F – 98 ( Reapproved ) Standard Test Method for Detecting Seal. Leaks in Porous. 1 This test method is under the jurisdiction of ASTM Committee F02 on Flexible Last previous edition approved in as F – ASTM F testing defines materials and a procedure that will detect and locate a leak equal or greater than a channel formed by a 50 μm ( in.) wire in.

Author: Tagal Samur
Country: Guyana
Language: English (Spanish)
Genre: Medical
Published (Last): 18 June 2018
Pages: 103
PDF File Size: 10.64 Mb
ePub File Size: 14.32 Mb
ISBN: 666-5-65800-147-4
Downloads: 88186
Price: Free* [*Free Regsitration Required]
Uploader: JoJora

ASTM F procedure requires that the dye penetrant have good contrast to the opaque packaging material. Here is a quick overview of ast changes: Please keep this in mind when developing your studies and validations. Packaging must be free of condensation or any other source of liquid water.

In the Burst Testair is introduced into the package at a predetermined pressure and flow rate.

f1929-9 If ASTM F testing is used as the quality control method, the test specimen must consist of a complete packaged device. The Creep Test provides a test for slow shear of the adhesive bond similar to a dead weight hanging on the seal.

Please contact us with any questions you may have about ASTM F, or if we can help you with any other testing questions or projects. If wicking does transpire, it may be verified by observing the porous side of the subject seal area.

  LM3171 DATASHEET PDF

Observe the package for any leaks originating from the inside edge of the package seal towards the outside edge of the package seal.

Overview of ASTM F Dye Penetration Integrity Test

Because air escapes through the walls of a porous package during inflation, the flow rate must be increased to compensate for the lost air through the walls and create the back pressure in the porous package. Requirements ASTM F testing is limited to porous materials which can retain the dye penetrant solution and prevent it from discoloring the entire seal for a minimum of 20 seconds.

Water already in the seal defects may render them undetectable with a dye penetrant. For more information visit www. Place a bead of solution between the two materials along the outer edge of the package seal, ensuring the entire outer edge of the seal is wetted with the dye solution. There is sstm general consensus regarding the level of leakage that is likely to be detrimental to a particular package. The porosity or lack thereof of the package material determines the inflation rate for the burst test.

Along the extended unsealed area beyond outer seal edgethe transparent material is separated from the porous material with use of a finger, paperclip, etc. The package will be visually inspected aatm dye penetration after contact with the dye penetrant for a specified time.

Observe each seal for a recommended duration of 5 to 20 seconds. As a guide, each Test Method above recommends observing each seal for a maximum of 5 seconds on a 4-sided package 20 seconds total.

  HP 4700N PDF

Overview of ASTM F1929 Dye Penetration Integrity Test

This pressure creates the force needed to rupture the seal. However, since ASTM F testing is designed solely to detect leakage, components that illustrate any indication of leakage are usually rejected.

Most commonly, an eyedropper or pipette is used to apply the f9129-98 penetration solution between the transparent and porous materials of the unsealed area.

The dye solution used in penetration testing will wick through any porous material over time, but normally not within the suggested maximum time. The Eyedropper method requires the packages to have an unsealed area that extends beyond the outer edge of the seal. Learn more about the different testing f1929–98 provided at each location. These leaks are frequently discovered at seals between package components of the same or dissimilar materials. A dye penetrant solution is applied locally to the seal edge to be tested for leaks.

Leaks may also result from a microscopic pinhole in the packaging material that is invisible to the human eye. Harmful biological or particulate contaminants may enter the device through leaks. The dye will have discolored the surface of the material.