Post Jobs

ADC0808 INTERFACING WITH 8051 PDF

This tutorial describes how to interface ADC to based Mircocontroller. The article also provides a sample tested Technology is an online. In This project (AT89S52) Microcontroller is interfaced with ADC IC to show the output value of ADC on LCD Screen,for a given variable input voltage. Interfacing ADC with three LDR using microcontroller and LCD. The project includes circuit diagram and source code in C.

Author: Yozshujora Malanris
Country: Argentina
Language: English (Spanish)
Genre: Technology
Published (Last): 11 April 2013
Pages: 269
PDF File Size: 10.56 Mb
ePub File Size: 20.61 Mb
ISBN: 382-8-13915-298-3
Downloads: 46388
Price: Free* [*Free Regsitration Required]
Uploader: Mezitilar

Log in or register to post Comment. SPI Module of Arduino. SPI Module of Arduino.

Interfacing ADC0808 To 8051

Moreover instead of polling for EOC just put some delay so instead of 12 lines you will require 10 lines. The circuit is divided into three parts: ADC gives ratio metric conversion output at its output pins. This Pin becomes High when the conversion has ended, so the controller comes to interacing that the data can now be read from the data pins.

In this project interacing have interfaced three channels of ADC And then ADC reads selected channel and send output to microcontroller.

SC pin6 of controller is connected to P1.

Therefore, we need an analog-to-digital converter to translate these analog signals to digital signals. An analog-to-digital converter is a device which converts continuous signals to discrete digital numbers. Typically, an ADC is an electronic device that converts an input analog voltage or current to a digital number proportional to the magnitude of the voltage or current.

The circuit describes how a D-flip flop can be used to provide the external clock. You are commenting using your WordPress. Thus, it provides continuous 8-bit digital output corresponding to instantaneous value of analogue input. On Sale Offers New Products. I have changed some modifications too but still its not working. The major advantage, of using ADC is that, we noise can be efficiently eliminated from the original signal and digital signal can travel more efficiently than analog one.

  BRIQUETAS DE BIOMASA PDF

What is Web Browser. I am jayanth This is a blog on electronics. So now whatever reading that you get from the ADC will be equal to the actual temperature.

A 16×2 LCD display is very basic intefracing and is ac0808 commonly used in various devices and circuits. A 9 volt battery and a 5 volt voltage regulator namely are used for powering the circuit. EOC, pin7 is connected to pin 3 P1. Typically, an ADC is an electronic device that converts an input analog voltage or current to a digital number proportional to the magnitude of the voltage or current.

Analog signal has infinite no of values like a sine wave or our speech, ADC inerfacing them into particular levels or states, which can be measured in numbers as a physical quantity. End of Conversion EOC This Pin becomes High when the conversion has ended, so the controller comes to know that the data can now be read from the data pins.

For selecting all the other input channels, have a look on the given table:. Rickey’s World Toggle sidebar.

Interface LDR using ADC 0808 to 8051

Reset and oscillator circuit is not shown in above circuit, But its needed for ALE Address latch enable, pin22 is given a low to high pulse to latch in the address. The device contains 8-channels.

  CONFESSION OF A BRITISH SPY HEMPHER PDF

Email required Address never made public. Skip to main content. Virgin Galactic — Commercial Space Flight. The circuit uses two ICs to divide the frequency by You can directly connect the Dith pin to Vcc. Choosing Battery for Robots. It works on the principle of successive approximation. It has a total of eight analogue input channels, out of which any one can be selected using address lines A, B and C.

ADC Interfacing With | EmbeTronicX (Embedded Tutorials Zone)

It is a 14 pin IC with two internal D flip flops. High — Low of the pulse. A clock of frequency KHz is generated using Timer0 in the interrupt mode. Retrieved from ” http: Here we are using external clock for clock input pin Fill in your details below or click an icon to log in: However, the circuit shown here is built to integfacing in its continuous mode without using any microprocessor. Get Our Weekly Newsletter!

As the conversion starts, EOC signal goes high. This circuit can be used as an intermediate circuit in many applications.

V in is input voltage for conversion V fs is full scale Voltage V z is zero voltage D x is data point being measure D max is Maximum data limit D min is Minimum data limit. Low- High of the Start Conversion pulse. You are commenting using your Twitter account.